Guide Line

 

 

2 to 3 weeks of beautiful nails with a deep color and beautiful shine!

Apply Bluesky Gellak/Polish in 6 steps:

  1. In case of unevenness, file the nails carefully with a very fine file
  2. Degrease the nails with Alcohol 70%, let it dry well
  3. Apply the Base coat and cure in a UV or LED lamp
  4. Apply the first color coat of Gellak and cure in a UV or LED lamp
  5. Apply a second color coat of Gellak and cure in UV or LED lamp
  6. Apply the Top coat and cure in a UV or LED lamp,
  7. Remove the adhesive layer with Alcohol 70%

To prevent bubbles or wrinkling of the Gellak, it is important to apply each layer thinly.

 


Remove Bluesky Gellak

  1. Lightly roughen the Top coat with file fine grit(180) or White Block
  2. Apply a little cuticle oil to the skin around the nail
  3. Apply Acetone to a cotton ball, or use our Remover Wraps
  4. Wrap the nail with cotton wool (on the nail) and Aluminum foil, or put the Wrap around your fingers, let it soak in for 15-20 minutes
  5. Remove the Cotton Pad + Aluminum Foil or the Wraps 6: Wipe off the Gellak, remnants can be removed with a Cuticle Pusher



Method Blossom Gellak with Blossom White Base
1: Apply base coat, cure in UV or LED lamp 2: Apply Blossom White base, cure in UV or LED lamp 3: Apply a second coat of Blossom White, do not cure 4: Make a creation with a nail art brush, e.g. a rose with the Blossom gel, cure in UV or LED lamp 5: Apply the Top coat, cure in UV or LED lamp
Note: White Color Blossom needs the Blossom Clear Base: base coat + normal black (or other color)
+ blossom clear base + blossom white + top coat.

Gum/Poly Gel
This can be used to lengthen or strengthen the nails. Pre-treatment - disinfect hands with skin disinfectant or wash hands with soap - file the nails to the desired length, gently push the cuticles back with a cuticle pusher - clean the nail plate with alcohol 70% - have the Gel brush, an orange woodstick or goat's leg and a small bowl of alcohol ready
Renew with tips
- apply a thin layer of Base Coat to the hard for 30 seconds under the lamp
- grab a tip and apply the Gum Gel to the inside of the tip with an orange woodstick or cuticle pusher
- dip the Gel Brush in the alcohol and spread the Gum Gel evenly over the tip
- press the tip firmly on the nail plate so that no air gets under it
- remove any remnants of Gum Gel with the Gel Brush
- Cure under the lamp for 1 minute
- pry the tip off the nail
- possibly file the nail wall or nail tip
- further finish the nails with a Top Coat or paint with a Gellak

 

If the natural nails are long enough, but a bit thin or limp, follow these steps:
- apply a thin layer of Base Coat and cure it under the lamp for 30 seconds
- apply a ball of Gum Gel on the middle of the nail
- moisten the Gel brush with alcohol
- spread the Gum Gel evenly over the nail
- Cure under the lamp for 1 minute
- possibly file some at the nail wall or nail end
- finish the nails with Top Coat or a Gellak

 

 

Hard Gel
degrease nails with 70% alcohol and allow to dry.

- apply a thin layer of Base Coat and cure it under the lamp for 30 seconds
- apply a thin layer of Hard Gel and cure it under the lamp for 1 minute
- possibly you can apply a second layer of Hard Gel and cure it for 1 minute as well
- apply a thin layer of Top Coat and cure it under the lamp for 30 seconds
- remove the adhesive layer with alcohol if necessary
You can also put the Hard Gel over the Gellak instead of under it.

 

 

cat eye
- apply the Base Coat and cure it under a lamp for 30 seconds - apply two coats of color and cure them individually. - apply the Cat Eye Gellak, hold the magnet just above the nail for 20 seconds and cure it under the lamp (the position of the magnet determines the direction of the Cat Eye) - apply the Top Coat - remove any adhesive layer with alcohol

 

Builder Gel

Natural Builder Gel (strengthening the nails)
- apply a thin layer of base coat
- apply a thin layer of Builder Gel (1 min curing)
- apply a second coat of Builder Gel (1 min curing)
- apply a thin layer of Top Coat
- remove the adhesive layer with alcohol
Builder Gel with Template

- apply a thin layer of Base Coat
- place a template tightly against the nail
- apply a layer of Builder gel and cure it for 1 min
- apply a second layer and cure for 1 min (after this you can remove the stencil)
- file on top of the nail with a 180 grit the nail smooth
- file to the desired length
- apply a layer of Top Coat
- remove any adhesive layer

 

Gellak MSDS sheets

Bluesky Gel Polish and Products are Hema Free

Chemical Structure

Bi-HEMA boasts a larger and more complex molecular structure than its HEMA counterpart, significantly decreasing penetration into biological tissue as well as sensitization potential for nail technicians regularly exposed to these chemicals.

Ingredients Bluesky Gel Polish